Merge pull request 'update 1.1' (#10) from Kubeadm_1_1 into main

Reviewed-on: #10

Networking/Debian-Static_IP.md

@@ -0,0 +1,129 @@
+**Debian Specific Static IP Address Setup**
+
+Get the interface name by looking at 
+
+```
+ip a
+```
+
+Example - here the interface we are targeting is enp1s0
+
+```
+~$ ip a
+1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
+    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
+    inet 127.0.0.1/8 scope host lo
+       valid_lft forever preferred_lft forever
+    inet6 ::1/128 scope host noprefixroute
+       valid_lft forever preferred_lft forever
+2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
+    link/ether 52:54:00:0c:f6:e7 brd ff:ff:ff:ff:ff:ff
+    altname enx5254000cf6e7
+    inet 192.168.50.80/24 brd 192.168.50.255 scope global dynamic noprefixroute enp1s0
+       valid_lft 85984sec preferred_lft 75184sec
+    inet6 2404:4400:4181:9200:5054:ff:fe0c:f6e7/64 scope global dynamic mngtmpaddr proto kernel_ra
+       valid_lft 86366sec preferred_lft 86366sec
+    inet6 2404:4400:4181:9200:617f:906e:3877:3f00/64 scope global dynamic mngtmpaddr noprefixroute
+       valid_lft 86366sec preferred_lft 86366sec
+    inet6 fe80::b2a2:4462:bece:c8b7/64 scope link
+       valid_lft forever preferred_lft forever
+~$
+```
+
+We will be updated the interfaces file int he networking dir.  
+Before we do anything we always make a backup copy 
+
+```
+sudo cp /etc/network/interfaces /etc/network/interfaces.bak
+```
+
+looking at the interface file its shows that the interface is set to dynamic
+
+** Orginal interface file
+
+```
+# This file describes the network interfaces available on your system
+# and how to activate them. For more information, see interfaces(5).
+
+source /etc/network/interfaces.d/*
+
+# The loopback network interface
+auto lo
+iface lo inet loopback
+
+# The primary network interface
+allow-hotplug enp1s0
+iface enp1s0 inet dhcp
+# This is an autoconfigured IPv6 interface
+iface enp1s0 inet6 auto
+```
+
+We will update the ***face enp1s0 inet dhcp***
+
+section to look like this 
+
+Example of updated file
+```
+# This file describes the network interfaces available on your system
+# and how to activate them. For more information, see interfaces(5).
+
+source /etc/network/interfaces.d/*
+
+# The loopback network interface
+auto lo
+iface lo inet loopback
+
+# The primary network interface
+allow-hotplug enp1s0
+iface enp1s0 inet static
+    address 192.168.50.20
+    netmask 255.255.255.0
+    gateway 192.168.50.254
+    dns-nameservers 192.168.50.254 8.8.8.8
+# This is an autoconfigured IPv6 interface
+iface enp1s0 inet6 auto
+```
+
+After you have made this edit you can restart the service to get the new IP address
+
+```
+luddie@Node1-master:~$ ip a
+1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
+    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
+    inet 127.0.0.1/8 scope host lo
+       valid_lft forever preferred_lft forever
+    inet6 ::1/128 scope host noprefixroute
+       valid_lft forever preferred_lft forever
+2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
+    link/ether 52:54:00:0c:f6:e7 brd ff:ff:ff:ff:ff:ff
+    altname enx5254000cf6e7
+    inet 192.168.50.20/24 brd 192.168.50.255 scope global enp1s0
+       valid_lft forever preferred_lft forever
+    inet 192.168.50.80/24 brd 192.168.50.255 scope global secondary dynamic noprefixroute enp1s0
+       valid_lft 86372sec preferred_lft 75572sec
+    inet6 2404:4400:4181:9200:617f:906e:3877:3f00/64 scope global dynamic mngtmpaddr noprefixroute
+       valid_lft 86369sec preferred_lft 86369sec
+    inet6 2404:4400:4181:9200:5054:ff:fe0c:f6e7/64 scope global dynamic mngtmpaddr proto kernel_ra
+       valid_lft 86369sec preferred_lft 86369sec
+    inet6 fe80::b2a2:4462:bece:c8b7/64 scope link
+       valid_lft forever preferred_lft forever
+luddie@Node1-master:~$
+```
+
+The network is now available via the updated ip address... HOWEVER did you see the old IP is still there?
+
+```
+inet 192.168.50.80/24 brd 192.168.50.255 scope global secondary dynamic noprefixroute enp1s0
+       valid_lft 86372sec preferred_lft 75572sec
+```
+
+Easiest way of dealing with this... 
+
+```
+sudo reboot
+
+```
+
+And when the machine comes back up, ssh using the newly statically assigned IP address.
+
+Update - Dont forget to updated the /etc/resolve.conf with your nameserver address

Networking/Hostname.md

@@ -0,0 +1,53 @@
+**Setup Hostname**
+
+Log into the hostname (ssh)
+
+Run the following command
+
+```
+sudo hostnamectl set-hostname NewHostName
+```
+
+Also need to update the hosts name
+
+```
+sudo vi /etc/hosts
+```
+
+***Example of old host file***
+
+```
+127.0.0.1       localhost
+127.0.1.1       old-hostname.vocus.co.nz old-hostname
+
+# The following lines are desirable for IPv6 capable hosts
+::1     localhost ip6-localhost ip6-loopback
+ff02::1 ip6-allnodes
+ff02::2 ip6-allrouters
+```
+
+***Example of updated host***
+
+```
+127.0.0.1       localhost
+127.0.1.1       New-hostname.vocus.co.nz New-hostname
+
+# The following lines are desirable for IPv6 capable hosts
+::1     localhost ip6-localhost ip6-loopback
+ff02::1 ip6-allnodes
+ff02::2 ip6-allrouters
+
+```
+
+While hostnamectl typically applies the changes immediately, some services or applications might still be referencing the old hostname. You can restart network services or reboot the system for a complete refresh, although often it's not strictly necessary.
+To restart network services:
+
+```
+sudo systemctl restart network-online.target
+```
+
+or just reboot
+
+```
+Sudo Reboot
+```

Networking/k8s/kubeadmin_install/Install_Instruction.md

@@ -0,0 +1,34 @@
+**Installing k8s with kubeadm**
+
+kubeadm join 192.168.50.20:6443 --token 72ckd0.rnphe03eqa135cjj \
+	--discovery-token-ca-cert-hash sha256:75add2111581b5b0a4a074f3748c46b67be82d246f110e557be049da0ef44941
+
+
+worker node 
+
+container runtime
+
+wget https://github.com/containerd/containerd/releases/download/v2.2.0/containerd-2.2.0-linux-amd64.tar.gz
+
+download the systemctl
+https://raw.githubusercontent.com/containerd/containerd/main/containerd.service 
+and move it to 
+
+sudo cp containerd.service /usr/lib/systemd/system
+
+runc
+download
+https://github.com/opencontainers/runc/releases/download/v1.4.0/runc.amd64
+
+
+
+sudo mkdir -p /etc/containerd
+ sudo containerd config default | sudo tee /etc/containerd/config.toml
+
+
+
+ sudo cat <<EOF | sudo tee /etc/sysctl.d/k8s.conf
+net.ipv4.ip_forward = 1
+EOF
+
+sudo sysctl --system

Networking/k8s/kubeadmin_install/add_users.md

@@ -0,0 +1,2 @@
+lol
+

SSH/keygen.md

@@ -8,7 +8,7 @@ On the new host
 ssh-keygen -t ecdsa
 ```
 
-you could add a -C for comment and then add your emaiul address but... meh
+You could add a -C for comment and then add your emaiul address but... meh
 
 
 Example 
@@ -39,3 +39,15 @@ The key's randomart image is:
 ~$
 
 ```
+
+This will generate 2 keys in the .ssh folder
+
+```
+~/.ssh$ ls
+id_ecdsa  id_ecdsa.pub
+~/.ssh$
+```
+
+Use can then cat the .pub file to get the public keyu for that host, which can be added to the authorized_host file of other machines to gain access.
+
+You can also create an authorized_keys on your cost, and add other ssh pub key to allow them to have direct access to this host.